problem with using spi on sam9g20

Discussion around AT91RM9200 and SAM9 Series Products.

Moderator: nferre

forti
Posts: 11
Joined: Thu Jun 07, 2012 8:34 am

problem with using spi on sam9g20

Mon Jan 07, 2013 11:09 am

hi all,
i am trying to use spi on at91sam9g20. on this web site
http://armbedded.eu/node/318
there are some instructions, which are compiling kernel , and making some changes on board-sam9g20.c file. i did these instructions, change my board's c file and compile kernel succesfully. But after all i cannot see /dev/spi on my board.

Are there anyone work with spi ? i really need some help.
what am i doing wrong?
thanks.
karlzeb
Posts: 2
Joined: Fri May 18, 2018 9:17 am

Re: problem with using spi on sam9g20

Fri May 18, 2018 9:30 am

Hallo everyone

I am having some problems with SPI on AT91SAM9G20

I am using kernel 2.6 and my target is SPI1

It is a commercial board with a 400Mhz part, but SPI1 is not supported by manufacturer, so i have to use registers

Went through the manual and did various check, but no success so far

Here is what i did

PIO register check (man pag 33): SPI1 is peripheral A on pins PB0,1,2

setdiopin does not change PB0 (MISO) so it seems there is a peripheral set there already

PIO Status Register PIO_PSR (man page 377): offset is 0x0008; base is 0xFFFF F600 (PIOB)

from shell : "devmem 0xFFFFF608 w "
i get 0x7FF80000 so peripheral is active (P13=0)

PIO AB Status Register PIO_ABSR (man page 388 ):offset is 0x0078 ;base is 0xFFFF F600 (PIOB)
from shell : "devmem 0xFFFFF678 w "
i get 0x00000000 so peripheral selected is A , correct

PMC register
Peripheral Clock Status Register PMC_PCSR (man page 302): offset is 0x0018,base is 0xFFFF FC00
from shell : "devmem 0xFFFFFC18 w "
default PCSR status is 0x003E021C (SPI1 clock is off ! )
need to write 3E221C

Peripheral Clock enable Register PMC _PCER offset is 0x0010
i only write bit 13
from shell : "devmem 0xFFFFFC10 w 0x00002000" works ! PCSR value changed

At this point i made a very simple shell script to test the basic functionality

here it is

#!/bin/bash
#SPI test script for T4200 using busybox commands

# -------------INIT-----------------

devmem 0xFFFFFC10 w 0x00002000 # enable SPI1 clock ; Peripheral Clock enable Register PMC_PCER man. pag 297

SPI1_BASE=FFFCC000 #base hex spi address

devmem $((0x$SPI1_BASE)) w 129 #reset and activate spi in slave mode; reg SPI_CR , offset=0x00 write-only

devmem $((0x$SPI1_BASE+4)) w 1 #activate spi master mode; reg SPI_MR , offset=0x04

devmem $((0x$SPI1_BASE+48)) w 0xFF02 #polarity leading edge capture, idle level low, minimum speed ; reg SPI_CSR0 man. pag 403

# -------------MAIN LOOP------------
while true
do
printf "Sending.. \n"
devmem $((0x$SPI1_BASE+12)) h 0x23 # transfer '#' ;reg SPI_TDR , offset=0x0C write-only

sleep 1
done





i also connected MISO and MOSI in a loop with a wire but nothing shows on my oscope.....
(gpio pins are working)

Any suggestion is appreciated

kind regards
blue_z
Location: USA
Posts: 1677
Joined: Thu Apr 19, 2007 10:15 pm

Re: problem with using spi on sam9g20

Tue May 22, 2018 12:03 am

karlzeb wrote:I am using kernel 2.6 and my target is SPI1
"2.6" really isn't specific enough. The version numbering for the Linux kernel changed at 3.0.

karlzeb wrote:It is a commercial board with a 400Mhz part,
What does that mean?
Are you trying to hack into some product that happens to have that SoC?

karlzeb wrote:Any suggestion is appreciated
What are you really trying to do?
If the kernel doesn't have SPI support, then you cannot hack the system to use some SPI slave device.

Regards
karlzeb
Posts: 2
Joined: Fri May 18, 2018 9:17 am

Re: problem with using spi on sam9g20

Tue May 22, 2018 9:43 am

Hallo

I am using SPI registers directly, no kernel support here; now it works anyway ; thanks !

Return to “SAM9 ARM9 MPU”

Who is online

Users browsing this forum: No registered users and 2 guests